If you are concerned about the performance of your brakes or would like them checked before going on a long journey please book an appointment in your local centre and our expert brake technicians will complete a free, no-obligation brake inspection. After the inspection we will provide you with a written brake report and a quote for any work which is required.
Please enter your vehicle registration below and click ‘Search’.
There are a number of tell-tale signs to look out for when using your brakes
Grinding – when the friction material on brake pads are heavily worn, this can result in a grinding noise as the brake pad has worn down to the metal caliper. This will likely damage the brake disc also.
Squeaking – there are many reasons why brakes squeal. It could suggest the brake caliper has stuck and the brakes pad remains partially applied to the disc but some pads have wear indicators that squeal when worn to let the driver know the brakes need changing. Either way, you should get this checked out.
Pulsating – If you feel a continuous pulsating from the brake pedal whenever you apply the brakes, this indicates the brake disc has become warped due to excessive heat. Pulsation occurs because the brake disc is distorted and no longer provides a perfectly flat surface when the brake pad makes contact. If this only occurs when you apply the brakes firmly, it could just be the ABS kicking in but you should have this checked out if you are concerned or it happens regularly.
Pulling – if your car pulls to the left or right when you apply the brakes this is usually indicative of a sticking hydraulic or mechanical component such as a seized caliper. An inspection can identify the precise reason for the vehicle pulling to one side.
Sponginess – the brake pedal feels spongy and the brakes seem unresponsive. This is a sign that air has entered the brakes lines and is preventing the brake fluid from flowing through this system effectively.
Soft Brake Pedal – if the brake pedal is limp and goes all the way to the floor, this indicates a serious braking system fault which you should have inspected immediately. A brake pedal that is soft and can be applied all the way to the floor usually means the brake fluid is ineffective and needs replacing but there can be several other potential reasons such as a master cylinder fault.
Dashboard Light – if a brake warning light appears on your instrument panel either continuously or when you apply the brakes it usually means the brake fluid level is critically low. This could also indicate a leak in the brake hoses.
High Handbrake – If the handbrake is pulling up higher than it normally does it may need adjusting. In modern cars, this is usually anything more than 6 to 8 clicks. If the handbrake lever reaches the end of its travel it will fail the MOT.
Old Brake Fluid – If your brake fluid is over 2 years old it may be losing its effectiveness since it has hygroscopic properties which means it absorbs moisture over time. This affects the properties of the fluid which negatively affects braking ability. Brake fluid should be change approximately every two years but check your manufacturers handbook.
For safety’s sake, it’s important to have your vehicle inspected as quickly as possible when you notice any of the above symptoms.
Regular brake checks are an important part of any vehicle preventative maintenance plan. Brake checks can identify a problem before it begins to impact on your braking efficiency, thus providing an opportunity to restore the effectiveness of your vehicle’s braking system to its intended operating performance. At M60 Autos we know how important the regular inspection and maintenance of your brakes can be to ensure your brakes continue to work effectively. We have over 5 brake specialists who are fully trained and committed to maintaining your brakes in an expert and cost effective manner.
Different driving patterns have a dramatic effect on how often your brakes need servicing.
For example, a set of brake pads could last up to 60,000 miles or more on a car driven mostly on the motorway. However the brakes on the same car driven mostly in busy city centre traffic may last only 25,000 miles or less.
Front brakes normally wear out before rear brakes because they handle a higher percentage of the braking load, especially on front-wheel drive cars.
It is often recommended that brake pads should be replaced if the pad friction material has worn down to a thickness of 3 millimetres. Brake disc thickness should be measured if they are at or below the manufacturer’s safe minimum thickness specification they should be replaced.
M60 Autos also recommends that brake discs or drums are replaced in axle sets. Replacing one brake disc or drum could cause an imbalanced braking performance that could lead to further premature wear.
When new parts are fitted, it’s vital to drive gently and carefully until they bed in, which takes approximately 200 miles. Excessive braking action on new parts can potentially damage them and lead to a loss of braking efficiency and performance.
As best practice for drivers whose annual mileage is considered average or high (around 8,000 miles per year or more), M60 Autos recommend that your vehicle’s braking system is checked at least twice a year. You may also want to check your braking system before a long journey or in advance of your MOT – your vehicle will fail its annual MOT test if your braking system does not meet required standards to allow your vehicle to come to an efficient stop.
To ensure your brakes are always at their best, we offer a unique brakes lifetime guarantee. Once you have pads or shoes fitted at M60 Autos, the replacement of these parts when they wear out is absolutely free to you, as long as you own the car. Additionally we will guarantee all other new brake parts fitted for the first 12 months after or the first 12,000 miles (whichever comes first).